Researched, not tested: every product in this post was chosen from the makers’ published specifications, labels and listings, not tried at home. How we research and choose products.
Knowing how to change the water in an AeroGarden matters more than any other bit of upkeep if you want the plants to keep producing. Topping off when the water light flashes keeps the pump going, but it never takes anything out. So week by week the bowl collects leftover salts from the plant food, bits of root and a film on the walls, while the nutrient balance drifts as the plants drink. A full change clears all of that in about fifteen minutes.

Everything here is written for the Harvest family, the most common AeroGarden, and the bigger models get their own notes near the end. Still deciding whether a countertop garden suits you at all? Is an AeroGarden worth it covers that first, and the best AeroGarden alternatives compares the gardens in the same class. If you’re new to growing in water, the beginner’s guide to apartment hydroponics explains why steady water matters so much.
How Often to Change the Water in an AeroGarden
It’s really three jobs, and each one runs on its own clock:
- Add water whenever the water light asks. On a Harvest, the blue water button flashes red when the bowl runs low and stops as soon as you top it up.
- Add plant food every 14 days. The green leaf button on a Harvest starts flashing on that schedule, and you tap it after feeding to restart the count.
- Empty and refill the whole bowl, which AeroGarden calls a “Rinse and Refill”. The maker suggests every 4 to 6 weeks and says its own lab saw clearly better growth in gardens that got one regularly.
Why Every 2 Weeks
A shorter cycle works better: a full change every 2 weeks, on the day the plant food reminder flashes. That’s my rule for any small active system, because a small bowl under a full deck of herbs changes fast. Plants pull some nutrients out quicker than others, so the mix slowly drifts from what the bottle intended, and leftover salts pile up between top-offs. A fresh bowl puts the solution back on the recipe. If you stay on AeroGarden’s own Liquid Plant Food and follow its reminders, the maker’s 4 to 6 weeks works too. Switch to bottled nutrients, though, and I wouldn’t stretch it past two weeks. Like a written record? The free printable hydroponics tracker has a box for every change.
Key takeaways
- Top off with plain pH-adjusted water when the water light flashes, and feed when the leaf light flashes every 14 days.
- Empty and refill the whole bowl every 2 weeks with fresh water and new plant food, even though AeroGarden’s own schedule is every 4 to 6 weeks.
- Keep the roots wet while the bowl is off: set the deck over a container of water and work steadily.
- Fill with room-temperature water to the Fill to Here line, never above it, and run a pump test before you walk away.
- Tap the leaf button after feeding so the nutrient reminder restarts its 14-day count.
Before You Start
Get everything out before you lift a thing, so the roots spend as little time out of water as possible:
- A jug of fresh water at room temperature, enough to fill the bowl.
- Your plant food, measured out by its label, or a bottled nutrient mixed to your crop’s EC.
- Somewhere to park the grow deck: a big bowl or pot with a few inches of water, wide enough that the roots can hang in it.
- A soft cloth or sponge. And a towel, because the counter will get wet.
If your tap water is very hard or strongly treated, can you use tap water for hydroponics explains when to filter or switch. With bottled nutrients, I’d always check the pH of the mixed solution and get it into the 5.5 to 6.5 range before it goes in.
Step by Step: A Full Water Change

The steps lean on AeroGarden’s help pages for the removable grow deck, the Fill to Here line and the pump test. The order around them is mine. Give yourself about fifteen minutes.
- Unplug the garden. Water and a live pump don’t mix, and an unplugged garden can’t kick its pump on while the bowl sits empty.
- Lift the grow deck straight up, plants and all, and rest it on your container so the roots hang into the water. You can coil long roots gently, but don’t tug them through the deck.
- Lift the bowl off the base and pour the old water down the sink. While it’s empty, look at the pump intake and pull any roots free by hand.
- Rinse the bowl with warm water and wipe off any film or crust with the cloth. That white crust near the waterline is calcium from the plant food. AeroGarden says it’s harmless, and it wipes right off.
- Refill to the Fill to Here line with room-temperature water. Give the plant food bottle a good shake, as AeroGarden advises, then add it now and stir, rather than pouring it over the roots.
- Set the bowl back on the base, then lower the grow deck into place and guide the roots down into the water.
- Plug in and run a pump test. On a Harvest, press and hold the leaf button for a few seconds and the pump runs for one minute. Listen for the hum and watch for moving water.
- Reset the nutrient reminder with a tap of the leaf button, so the next 14-day count starts today.
Tip. Do the change right after a harvest. A freshly cut deck is lighter, so it’s easier to lift, and the roots slide back in with less fuss. You’ll also have fewer wet leaves dripping on the counter. How to prune hydroponic basil covers where to cut.
If the Roots Have Filled the Bowl
Give basil or mint a couple of months and the roots can fill the bowl and wrap around the pump. Keep the healthy white ones. Anything brown, slimy or tangled around the pump intake gets cut back with clean scissors. Roots also push through the nozzles on the grow deck and slow the water. AeroGarden notes that the deck comes apart on most models, so you can clean those out between plantings. Brown all over and smelly? That’s rot rather than overgrowth, and hydrogen peroxide for root rot explains the rescue.
Between Changes: Topping Off

Between full changes, add water whenever the water light flashes, or once a day if your kitchen runs warm. Use plain pH-adjusted water, not more plant food. As the plants drink, whatever’s left in the bowl gets more concentrated, so feeding at every top-off just keeps pushing the strength up. Feed on the 14-day reminder or at the full change. Nothing in between. If the garden is brand new, AeroGarden setup and the first week covers the days before that first reminder.
Water light still flashing when the bowl is obviously full? The float may be stuck. AeroGarden’s fix is to pull the tube out of the water bowl, fish the float out with a magnet, drop it back in the tube and reconnect the tube to the base. Topping off hydroponic water goes into why plain pH-adjusted water is the right top-off, and how often to change hydroponic water covers the thinking behind the 2-week schedule.
What Water and Plant Food to Use
Plain tap water is fine in most homes, although hardness varies a lot. AeroGarden calls its Liquid Plant Food a pH-buffered mineral blend, which helps it hold a sensible pH in typical tap water. Very hard water leaves more crust and can push the pH up. Very soft or filtered water is the opposite case, since it brings few minerals of its own. Spring, distilled and RO water for hydroponics compares the options.
You don’t have to stay on AeroGarden’s food, though. A bottled hydroponic nutrient and your own seeds cost less over a year, and replacing AeroGarden pods and plant food shows how. My one rule: switch only at a full water change. Never mix two brands in one bowl. The pH and nutrient calculator works out the dose for a small bowl, and a pH meter confirms it.
Mistakes That Stress the Roots
| Mistake | What happens | Instead |
|---|---|---|
| Leaving roots in the open air | Fine root tips dry and die within minutes | Rest the deck over water while you work |
| Refilling with cold water straight from the tap | A sudden temperature drop shocks the roots | Use water at room temperature |
| Filling above the Fill to Here line | Water can spill into the base or over the counter | Stop at the line, since AeroGarden advises keeping the water at or just below it |
| Adding plant food at every top-off | The solution grows stronger as plants drink, and leaf tips burn | Top off with plain pH-adjusted water, feed on the 14-day reminder |
| Washing the bowl with dish soap | Any soap left behind harms roots | Rinse with warm water and wipe; save deep cleaning for between plantings |
| Forgetting the pump test | A pump knocked loose runs dry, and the plants wilt by evening | Hold the leaf button and listen before you leave |
| Not resetting the reminder | The leaf light keeps flashing, and you lose track | Tap the leaf button after feeding |
Green film on the bowl walls is a separate problem, though: it means light is reaching the water. Keep the empty pod holes capped, and see why algae keeps growing for the fix. Between plantings, I’d give the bowl and deck a proper clean, and cleaning a small hydroponic system walks through it with 3% hydrogen peroxide, which leaves nothing behind.
Bigger AeroGarden Models
On any AeroGarden the routine doesn’t change: unplug, lift the deck, empty, rinse, refill, reconnect, test the pump. Only the buttons move. For the bigger models, the steps come from AeroGarden’s help pages. They say a Harvest Elite runs its pump test from the menu under the leaf button, while a Bounty or Farm has a Test Pump option in its pump settings. A Bounty bowl holds more water under a bigger deck of plants, so it’s easier with a second pair of hands, or with the plants trimmed first.
Going away? AeroGarden lists Vacation Mode, which cuts water use while you’re out, on the Harvest Elite, Bounty and Farm, but not on the basic Harvest. With a plain Harvest, do a full change and fill to the Fill to Here line right before you leave, as the feeding schedule for travelers describes. I’d also use the seed to harvest calculator to time the trip around your next harvest.
Where these facts come from
The water and leaf lights, the 14-day plant food reminder, the 4 to 6 week Rinse and Refill, the harmless calcium crust, the Fill to Here line, the float reset, the pump tests by model, the separable grow deck and the models with Vacation Mode all come from AeroGarden’s help center FAQs, read in October 2026. The 2-week full change, plain pH-adjusted water top-offs and the pH range are this site’s standard settings for small systems, and the order of the steps around those help-center details is this site’s own.
One Last Tip
Treat the water change as a check-up, not just a chore. It’s the only time you see the whole root mass at once, out of the bowl and in good light. White roots and old water that smells of almost nothing mean the garden is fine. Brown tips, slime or a pond smell mean something has started to go wrong, and you’ve spotted it while the leaves still look happy. I’d much rather catch it there than wait for the plants to droop.
Frequently Asked Questions
How often should I change the water in my AeroGarden?
AeroGarden says every 4 to 6 weeks. A full change every 2 weeks works better, on the day the plant food light flashes, because a small bowl drifts fast once the plants are drinking hard. In between, just top off with plain pH-adjusted water when the water light asks.
Can I change the water without removing the plants?
Yes, and that’s the easy way. The plants stay in the grow deck. Lift it out, rest it over a container of water so the roots stay wet, then rinse and refill the bowl and lower the deck back in. The roots are only out of the bowl for a few minutes.
How often do you add plant food to an AeroGarden?
Every 14 days. A Harvest reminds you by flashing the green leaf button, and you tap it after feeding to restart the count. Top off with plain pH-adjusted water in between, since feeding every time you add water makes the bowl stronger and stronger.
Can I use tap water in an AeroGarden?
Yes, in most homes. AeroGarden’s Liquid Plant Food is pH-buffered, which helps with typical tap water. If yours is very hard, expect more white crust and a higher pH, and I’d think about filtered or bottled water.
What is the white crust in my AeroGarden bowl?
It’s calcium buildup from the Liquid Plant Food, according to AeroGarden, and it isn’t harmful. It collects near the waterline. Wipe it off at each full change, and it won’t build up, though hard tap water makes more of it.
Why does my AeroGarden say add water when it is full?
The float that senses the water level may be stuck. AeroGarden says to remove the tube in the water bowl, lift the float out with a magnet, put it back in the tube and reconnect the tube to the base. If the alert still won’t stop, contact AeroGarden support.
How do I check the pump after a water change?
Run a pump test before you walk away. On a Harvest, hold the leaf button down for a few seconds and the pump runs for one minute. A Harvest Elite keeps the test in the menu under the leaf button, and a Bounty or Farm puts it under the pump settings.
Should I trim the roots when I change the water?
Only if they need it. I’d leave healthy white roots alone and cut back anything brown, slimy or wrapped around the pump intake with clean scissors. Brown and smelly all over is root rot, though, and that needs treating rather than trimming.
Can I wash the AeroGarden bowl with soap?
Not during a routine change, because any soap left behind harms roots. Warm water and a soft cloth handle the film and crust. Save the proper clean for between plantings, and use 3% hydrogen peroxide rather than harsh cleaners.
Does the AeroGarden Harvest have a vacation mode?
No. AeroGarden lists Vacation Mode on the Harvest Elite, Bounty and Farm models only. With a basic Harvest, do a full water change right before a trip and fill to the Fill to Here line, so the plants start with as much water and fresh food as the bowl holds.



